I have been building this car for the past 13 years on and off. By the time I was ready to put it on the track, Covid happened and then so did marriage and 2 kids. I am selling due to the fact I don’t have time for it anymore and having a house and other responsibilities are expensive. Instead of letting it just sit around until I can do more track days, I figured I’d sell it. I bought 2 1994 325is. The chassis has around 160kmi on it and the motor has around 90kmiles.
The engine came from a vehicle with a bent chassis. I replaced pretty much every single nut and bolt along with every bushing. The front and rear subframe have been reinforced. The oil pan baffle was welded in by Turner Motorsports. The roll cage was installed by Jim at Rollcage components in VA.
I built the car to race in SCCA spec e36 and NASA. The only things you would need to do is install a fire protection system, new Harnesses and window nets, as those materials are all dated. I do have the old ones and they will be included with the car. There is probably some stuff I left out but these parts that I mentioned, I have receipts for all of them.
Only serious inquires. The car is not registered but we might be able to take the car for a spin around the block. I have a lift as well so we can also put it up and look under it.
The title is clean and in hand.
Vin# WBABF3329RDE44440
Price: 12,500 OBO
Parts
- 6-point Roll cage 1.75x120 DOM installed by rollage components in VA TMS#568461 17mm 12x1.5Bullet Nose Racing Wheel Studs with Dry Lube
TMS Poly Tow strap with Bolt
TMS Oil Pan Baffle - welded in
VAC Floor mount Adapters
VAC Lap Belt Mounting Bracket
VAC Anti-sub Mounting Bar
VAC Seat Slider
OMP RS-PT2 Racing Seat
Kirkey Aluminum Floor seat mount
Kirkey Intermediate Road Racing Seat 17% 15 degree Layback w/ seat cover
МКАН Motorsports Diamond Plate floor set
HARD Motorsport e36 Dash Block off Panel Kit
HARD Motorsport Kill Switch
Mishimoto Radiator
Bimmerworld Front Windshield Defroster
Kosei K1 Racing 17x8.5 5x120 ET40 Wheels
P225/45R17 94w Toyo Proxes R888
AKG Motorsport Rear Lower Adjustable Control Arms w/ spherical bearings
Prosport Performance Water Temp sender hose adapter
Prosport Perfromance EVO series Oil Pressure sensor and 52mm gauge Prosport Performance EVO series Water Temperature and 52mm gauge
Prosport Performance EVO series Oil Temperature and 52mm gauge
Bimmerworld Oil distribution block
SPAL Auxillary Fan
New ebrake cables
New ebrake shoes
New Front Control Arms
New Wheel Bearings
New Guibo/flex disc w/ bolts and nuts
New Driveshaft Center Support Bearing
New sway bar Endlinks and Powerflex bushings
New Axles
New Clutch Slave Cylinder
TMS Rear trailing Arm bushing Limiter Kit Bimmerworld Stainless Steel Brake Line Kit
New Rear upper control arms with bushings
Front and Rear Hawk DTC-60 Track only Brake Pads
Power Flex Rear Subframe bushings
Power Flex Differential Bushings
AKG Motorsport Front Control Arm Bushings
New Thermostat and Housing
New Expansion Tank and Radiator Cap
Refurbished Rack and Pinion
New Inner and Outer Tie Rod ends with boots
Front Subframe Reinforcement Kit
New Motor Mounts
New Transmission Mounts
New Fuel Pump
Extras
I have a ton of extras, from body parts to mechanical parts to suspension parts everything will be going with the car.
Pictures:
https://imgur.com/a/NFcuMvS